ROSEBUD-RUSH Gets Conditional Pass on Health Inspection - Chicago Restaurant

MANAGEMENT, FOOD EMPLOYEE AND CONDITIONAL EMPLOYEE; KNOWLEDGE, RESPONSIBILITIES AND REPORTING - Comments: NO EMPLOYEE HEALTH POLICY ON PREMISES. INSTRUCTED MANAGER MUST PROVIDE AN EMPLOYEE HEALTH POLICY ON PREMISES. PRIORITY FOUNDATION. NO CITATION ISSUED.

Ill food workers cause 70% of foodborne outbreaks. Proper reporting prevents transmission of Norovirus, Hepatitis A, Salmonella, and other serious diseases.

All food employees must understand and follow health reporting requirements and food safety responsibilities.

Employees must: Report illness symptoms and exposures; Be excluded/restricted when ill; Understand their role in preventing foodborne illness; Follow proper hygiene practices; Have signed health policy on file.

PROCEDURES FOR RESPONDING TO VOMITING AND DIARRHEAL EVENTS - Comments: NO VOMIT AND DIARRHEA CLEANING PROCEDURE WITH BIOHAZARD CLEAN-UP KIT ON PREMISES. INSTRUCTED MANAGER MUST PROVIDE A VOMIT AND DIARRHEA CLEANING PROCEDURE WITH BIOHAZARD CLEAN-UP KIT ON PREMISES. PRIORITY FOUNDATION. NO CITATION ISSUED.

Vomit and diarrhea contain millions of viral particles. One incident can contaminate entire facility and cause outbreak affecting dozens.

Written procedures required for cleaning bodily fluid events to prevent disease transmission.

Written procedure must address: Isolating contaminated area; Removing and discarding affected food; Using proper PPE; Cleaning and sanitizing with appropriate concentration; Proper disposal of contaminated materials.

PROPER COLD HOLDING TEMPERATURES - Comments: OBSERVED THE FOLLOWING TIME/TEMPERATURE CONTROL FOR SAFETY FOODS HELD AT IMPROPER TEMPERATURES- CHEESE AT 55.0 F, COOKED BROCCOLI AT 56.0 F, COOKED ASPARAGUS AT 55.0 F, ANGEL HAIR PASTA AT 56.0, FETUCCINI AT 55.0 FAND MEAT BALLS AT 55.0 F. INSTRUCTED MANAGER ALL TIME/TEMPERATURE CONTROL FOR SAFETY FOODS MUST BE HELD AT 41.0 F OR BELOW IF HELD COLD. ALL SAID OUT OF TEMPERATURE TCS FOODS HAVE BEEN VOLUNTARILLY DISCARDED. PRIORITY VIOLATION 7-38-005.

Temperatures below 135°F allow bacteria to multiply, especially spore-formers that survive cooking.

Hot foods must be held at 135°F or above.

Maintain 135°F or above; Check temperatures regularly; Proper hot holding equipment; Cannot reheat in hot holding units.

CONSUMER ADVISORY PROVIDED FOR RAW/UNDERCOOKED FOOD - Comments: NO DISCLOSURE OR REMINDER ON CONSUMER ADVISORY ON MENUS. INSTRUCTED MANAGER MUST PROVIDE DISCLOUSRE AND REMINDER ON CONSUMER ADVISORY/MENUS. PRIORITY FOUNDATION. NO CITATION ISSUED.

Dirty surfaces attract pests and can contaminate food indirectly.

Non-food contact surfaces must be kept clean.

Clean as often as necessary; Remove grease and debris; Maintain equipment exteriors; Keep walls, ceilings, floors clean.

PROPER COOLING METHODS USED; ADEQUATE EQUIPMENT FOR TEMPERATURE CONTROL - Comments: FOUND BOTH PASTA STAND UP COOLER AND 2-DOOR REACH IN PREP COOLER (BY PASTA COOKING STATION) AMBIENT AIR TEMPERATURE AT 55.0 F, FOUND COOKED PASTA, COOKED BROCCOLI, ETC. HELD INSIDE SAID COOLERS. PRIORITY VIOLATION 7-38-005.

Dirty equipment harbors bacteria and attracts pests.

All equipment and utensils must be clean and properly maintained.

Equipment clean to sight and touch; Free of food debris and grease; Maintained in good repair; Stored properly when clean.

FOOD & NON-FOOD CONTACT SURFACES CLEANABLE, PROPERLY DESIGNED, CONSTRUCTED & USED - Comments: PREP AREA 1-DOOR REACH IN COOLER (BY DISHMACHINE) DOOR RUBBER GASKET RIPPED. INSTRUCTED MANAGER TO REPLACE DAMAGED DOOR RUBBER GASKET.

Poor design creates areas that harbor bacteria.

All surfaces must be designed to be easily cleanable.

Smooth, non-porous surfaces; Free of cracks and crevices; Easily disassembled; Accessible for cleaning.

FOOD & NON-FOOD CONTACT SURFACES CLEANABLE, PROPERLY DESIGNED, CONSTRUCTED & USED - Comments: PREP AREA 1-DOOR REACH IN COOLER (BY DISHMACHINE) DOOR RUBBER GASKET RIPPED. INSTRUCTED MANAGER TO REPLACE DAMAGED DOOR RUBBER GASKET.

Poor design creates areas that harbor bacteria.

All surfaces must be designed to be easily cleanable.

Smooth, non-porous surfaces; Free of cracks and crevices; Easily disassembled; Accessible for cleaning.