ZOOTS Gets Conditional Pass on Health Inspection - Chicago Restaurant

PROPER COLD HOLDING TEMPERATURES - Comments: NOTED INTERNAL TEMPERATURE OF THE FOLLOWING TCS FOOD ITEMS INSIDE SERVICE COOLERS TO BE IMPROPER:-TURKEY 48.7F, HAM 58.6F, SALOMI 53.1F, MUSHROOMS 45.5F, BEEF 43.9F, CHEESE 50.5F. MANAGER IMMEDIATELY AND VOLUNTARILY DISPOSED OF 4 LBS OF PRODUCTS WORTH $19.00 THROUGH DENATURING PROCESS. PRIORITY VIOLATION #7-38-005. CITATION ISSUED.

Temperatures below 135°F allow bacteria to multiply, especially spore-formers that survive cooking.

Hot foods must be held at 135°F or above.

Maintain 135°F or above; Check temperatures regularly; Proper hot holding equipment; Cannot reheat in hot holding units.

APPROVED THAWING METHODS USED - Comments: NOTED ASORTED FOOD ITEMS IN WATER INSIDE CONTAINER IN THE 3 COMPARTMENT SINK THAWING. MANAGER STATED THAT THE FOOD ITEMS WERE DEFROSTING. DISCUSSED WITH MANAGEMENT THE DIFFERENT METHODS OF DEFROSTING FOOD:- EITHER UNDER COLD RUNNING WATER OR INSIDE THE REFRIGERATION UNIT. PRODUCT TEMPERATURE WAS ADEQUATE AT THE TIME.

Damaged surfaces cannot be properly cleaned and may harbor pests.

Walls and ceilings must be smooth, cleanable, and in good repair.

Smooth, washable surfaces in food areas; Light colored; No holes or cracks; Clean and maintained.

FOOD & NON-FOOD CONTACT SURFACES CLEANABLE, PROPERLY DESIGNED, CONSTRUCTED & USED - Comments: NOTED RUSTY AND DIRTY SHELVES INSIDE WALK IN COOLER AT THE BASEMENT KITCHEN PREP AREA. INSTRUCTED TO DETAIL CLEAN, REPAINT WITH NON TOXIC FOOD GRADE PAINT AND/OR REPLACE.

Poor design creates areas that harbor bacteria.

All surfaces must be designed to be easily cleanable.

Smooth, non-porous surfaces; Free of cracks and crevices; Easily disassembled; Accessible for cleaning.

FOOD & NON-FOOD CONTACT SURFACES CLEANABLE, PROPERLY DESIGNED, CONSTRUCTED & USED - Comments: NOTED SOME USE OF MILK CRATES FOR ELEVATION AT THE KITCHEN AREA, DISHWASHING AREA AND DRY STORAGE AREA. INSTRUCTED NOT TO USE MILK CRATES FOR ELEVATION TO PREVENT HIDING PLACES FOR PEST. MUST PROVIDE APPROPRIATE SHELVING FOR STORAGE. ALL FOOD ITEMS MUST ALSO BE STORED 6" AWAY FROM THE WALL

Poor design creates areas that harbor bacteria.

All surfaces must be designed to be easily cleanable.

Smooth, non-porous surfaces; Free of cracks and crevices; Easily disassembled; Accessible for cleaning.

FOOD & NON-FOOD CONTACT SURFACES CLEANABLE, PROPERLY DESIGNED, CONSTRUCTED & USED - Comments: NOTED ICE BUILD UP INSIDE THE WALK IN FREEZER ON THE FLOOR AND SHELVES. INSTRUCTED TO REPAIR AND MAINTAIN THE CONDENSATION UNITS.

Poor design creates areas that harbor bacteria.

All surfaces must be designed to be easily cleanable.

Smooth, non-porous surfaces; Free of cracks and crevices; Easily disassembled; Accessible for cleaning.

PLUMBING INSTALLED; PROPER BACKFLOW DEVICES - Comments: NOTED LEAKING FAUCET AT THE 3 COMARTMENT SINK OF THE BASEMENT FOOD PREP/DRY STORAGE AREA. INSTRUCTED TO REPAIR AND MAINTAIN.

Backflow can contaminate entire water supply with sewage or chemicals.

Plumbing must be properly installed with backflow prevention.

Air gaps at fixtures; Backflow preventers on connections; No cross-connections; Annual testing of devices; Proper drainage.

PLUMBING INSTALLED; PROPER BACKFLOW DEVICES - Comments: NOTED SPRAYER AT THE 3 COMPARTMENT SINK HANGING BELOW THE RIM OF THE SINK AT THE BASEMENT FOOD PREP/DRY STORAGE. INSTRUCTED TO PROVIDE THE DEVICE TO HOLD THE SPRAYER ABOVE THE WATER RIM OF THE 3 COMPARTMENT SINK.

Backflow can contaminate entire water supply with sewage or chemicals.

Plumbing must be properly installed with backflow prevention.

Air gaps at fixtures; Backflow preventers on connections; No cross-connections; Annual testing of devices; Proper drainage.

PLUMBING INSTALLED; PROPER BACKFLOW DEVICES - Comments: NOTED SPRAYER AT THE 3 COMPARTMENT SINK HANGING BELOW THE RIM OF THE SINK AT THE BASEMENT FOOD PREP/DRY STORAGE. INSTRUCTED TO PROVIDE THE DEVICE TO HOLD THE SPRAYER ABOVE THE WATER RIM OF THE 3 COMPARTMENT SINK.

Backflow can contaminate entire water supply with sewage or chemicals.

Plumbing must be properly installed with backflow prevention.

Air gaps at fixtures; Backflow preventers on connections; No cross-connections; Annual testing of devices; Proper drainage.